Home ProductsDigital Refrigeration Controller

XR60CX Dixell Freezer Controller 32x74mm For Coldroom

XR60CX Dixell Freezer Controller 32x74mm For Coldroom

  • XR60CX Dixell Freezer Controller 32x74mm For Coldroom
  • XR60CX Dixell Freezer Controller 32x74mm For Coldroom
  • XR60CX Dixell Freezer Controller 32x74mm For Coldroom
  • XR60CX Dixell Freezer Controller 32x74mm For Coldroom
XR60CX Dixell Freezer Controller 32x74mm For Coldroom
Product Details:
Place of Origin: Italy / China
Brand Name: Dixell
Certification: EAC
Model Number: XR60CX
Payment & Shipping Terms:
Minimum Order Quantity: 5 sets
Price: negotiate
Packaging Details: cartons
Delivery Time: 4-6 weeks
Payment Terms: T/T
Supply Ability: 1000pcs per weeks
Contact Now
Detailed Product Description
Function: Temperature Display,control And Adjust Screen Display: Red
Application: Chiller,Freezer And Other Cooling Equipment Name: Dixell Ditital Controller
Sensor: PTC Power: 220V/110V
High Light:

32x74mm Refrigeration Temperature Control

,

XR60CX Dixell Freezer Controller

,

XR60CX digital thermostat controller

XR60CX Dixell Digital Refrigeration Controllers,Digital Temperature Controller For Coldroom And Freezer

GENERAL DESCRIPTION
 
Model XR60CX, format 32 x 74 mm, is microprocessor based controller, suitable for applications on
medium or low temperature ventilated refrigerating units. It has three relay outputs to control
compressor, fan, and defrost, which can be either electrical or reverse cycle (hot gas). It is also
provided with three NTC or PTC probe inputs, the first one for temperature control, the second one,
to be located onto the evaporator, to control the defrost termination temperature and to managed the
fan, the third one, optional, to connect to the HOT KEY terminals to signal the condenser
temperature alarm or to display a temperature. The digital input can operate as fourth temperature
probe.
 
The HOT KEY output allows to connect the unit, by means of the external module XJ485-CX, to a
network line ModBUS-RTU compatible such as the dIXEL monitoring units of X-WEB family. It
allows to program the controller by means the HOT KEY programming keyboard.
The instrument is fully configurable through special parameters that can be easily programmed
through the keyboard.
 
SPECIFICATIONS / MODELS 
 
  XR01CX XR02CX XR03CX XR04CX XR06CX
Dimension          
32*74*50mm  
32*74*60mm        
Power supply          
12,24V ac/dc (± 10%)
115,230V ac/dc (± 10%)
Temperature sensor          
Coldroom Temp Probe NTC / PTC √ / optional √ / optional √ / optional √ / optional √ / optional
Defrost / Fan Probe NTC / PTC √ / optional √ / optional √ / optional √ / optional √ / optional
Function digital signal input  
Outout          
Load or compressor 20A / 8A 20A / 8A 20A / 8A 20A / 8A 20A / 8A
Defrost   Shut down defrost Shut down defrost 8A 8A
Fan         8A
Light / Auxiliary output     8A    
Others          
Hot Key Programming key
Heating / Cooling Heating / Cooling Heating / Cooling Heating / Cooling Cooling Cooling

 

 

  XR10CX XR20CX XR30CX XR40CX XR50CX XR60CX XR70CX
Dimension              
32*74*60mm
Power supply              
12,24V ac/dc (± 10%)  
115,230V ac/dc (± 10%)
Display              
3 digital tubes, minus sign,Decimal point,Output status minus sign
Temperature sensor              
Coldroom Temp Probe NTC / PTC
Evaporator Probe NTC / PTC
second Evaporator Probe NTC / PTC      
Condenser Probe NTC / PTC
Digital input/display probe              
Alarm,Trigger Defrost,Auxiliary probe, door switch,Pressure switch Settable Settable Settable Settable Settable Settable Settable
Relay Outout              
compressor 20A / 8A 20A / 8A 20A / 8A 20A / 8A 20A / 8A 20A / 8A/16A 20A / 8A/16A
Defrost       8A 8A 8A 8A/16A
Evaporator Fan           5A/8A 5A/16A
Light / Alarm output     8A   5A/8A   8A/16A
Others              
Hot Key Programming key
Serial Interface MODBUS
 
DEFROST
 
Two defrost modes are available through the “td” parameter:
 
• td=EL → defrost through electrical heater (compressor OFF)
• td=in → hot gas defrost (compressor ON).
 
Other parameters are used to control the interval between defrost cycles (id) ), its maximum length (Md) and two defrost modes: timed or controlled by the evaporator’s probe. At the end of defrost dripping time is started, its length is set in the dt parameter. With dt=0 the dripping time is disabled
 
FANS
With FC parameter it can be selected the fans functioning:
 
• FC=cn → will switch ON and OFF with the compressor and not run during defrost
• FC=on → fans will run even if the compressor is off, and not run during defrost
 
After defrost, there is a timed fan delay allowing for drip time, set by means of the “Fd” parameter.
 
• FC=cy → fans will switch ON and OFF with the compressor and run during defrost
• FC=oY → fans will run continuously also during defrost.
 
An additional parameter “FS” provides the setting of temperature, detected by the evaporator probe, above which the fans are always OFF. This is used to make sure circulation of air only if his temperature is lower than set in “FS”
 
FANS AND DIGITAL INPUT
 
When the digital input is configured as door switch iF=do, fans and compressor status depends on the dC parameter value:
• dC=no → normal regulation;
• dC=Fn → fans OFF;
• dC=cP → compressor OFF;
• dC=Fc → compressor and fans OFF.
When rd=y, the regulation restart with door open alarm.
 
FRONT PANEL COMMANDS
XR60CX Dixell Freezer Controller 32x74mm For Coldroom 0
 

XR60CX Dixell Freezer Controller 32x74mm For Coldroom 1

 

HOW TO SEE THE SET POINT
 
1.Push and immediately release the SET key, the set point will be showed;
2.Push and immediately release the SET key or wait about 5s to return to normal visualisation.
 
HOW TO CHANGE THE SETPOINT
1.Push the SET key for more than 2 seconds to change the Set point value;
2.The value of the set point will be displayed and the “°C” or “°F” LED starts blinking;
3.To change the Set value push the or arrows.
4.To memorise the new set point value push the SET key again or wait 10s.
 
HOW TO START A MANUAL DEFROST
Push the DEF key for more than 2 seconds and a manual defrost will start
 
HOW TO CHANGE A PARAMETER VALUE
To change the parameter’s value operate as follows:
1. Enter the Programming mode by pressing the SET+keys for 3s (“°C” or “°F” LED starts blinking).
2. Select the required parameter. Press the “SET” key to display its value
3. Use ↑ or ↓  to change its value.
4. Press “SET” to store the new value and move to the following parameter.
 
To exit: Press SET+↑ or wait 15s without pressing a key.
NOTE: the set value is stored even when the procedure is exited by waiting the time-out to expire.
 
ALARM SIGNALLING
 
Mess.          Cause                                             Outputs
"P1"              Room probe failure                          Compressor output according to “Cy” e “Cn”
"P2"              Evaporator probe failure                  Defrost end is timed
"HA"              Maximum temperature alarm            Outputs unchanged
"LA"              Minimum temperature alarm             Outputs unchanged
“EA”              External alarm                                  Outputs unchanged
“CA”              Serious external alarm                     All outputs OFF
“dA”               Door Open                                      Compressor and fans restarts
 
 
XR60CX Dixell Freezer Controller 32x74mm For Coldroom 2
 
 
 
 

 

Contact Details
Shenzhen Sino-Australia Refrigeration Equipment Co., Ltd.

Contact Person: Jason

Tel: 86-13480948557

Send your inquiry directly to us (0 / 3000)

Other Products